Wireless Charging in Plain Words: Pads, Magnets, and Why It Is Slower
Set the phone down on a pad, and it charges — no plug to find, no tiny connector to aim. For stiff fingers and a dark nightstand, that ease is the whole point. The trade is speed: wireless is the gentle option, not the fast one. This lesson covers the parts worth knowing — alignment, magnets, cases, and warmth.
How it works — and its one weakness
Inside the pad and inside the phone are two coils of wire. Line them up, and power crosses the little gap between them — nothing to plug in, nothing to wear out. That is also the weakness: alignment is everything. A phone set down crooked — half off the pad, nudged by the cat — can charge painfully slowly, or stop altogether. Most “dead phone in the morning” stories are a phone that spent the night two inches from where it needed to be.
Magnets fix the aim: MagSafe and Qi2
Apple’s answer is MagSafe: a ring of magnets in the iPhone — every iPhone 12 and later, except the SE models and the 16e — and in the charger, which snap together in exactly the right spot. You can feel it land. The shared standard behind all wireless charging is called Qi (say “chee”), and its newer version, Qi2, borrowed the magnet idea — so a growing number of Android phones snap into place the same way. A plain Qi pad will still charge any Qi phone; there is just no snap, so the centering is up to you.
Why it is slower — and how much slower
- A plain Qi pad gives an iPhone about 7.5 watts — a slow, overnight pace.
- MagSafe does better: up to 15 watts on iPhone 12 through 15, and up to 25 watts on iPhone 16 and later — but only with the newer MagSafe charger and a wall plug of 30 watts or stronger. The pad cannot give what the plug does not send.
- Samsung’s fast wireless charging tops out around 15 watts, with Samsung’s own fast charger and a strong enough wall plug.
- A cable beats them all. Leaving in an hour with the battery at 10%? Plug in. Going to bed? The pad is perfect.
Cases, cards, and warmth
- Ordinary cases are fine. Wireless power passes through most cases up to about 3 millimeters thick. Thick cases, metal backs, metal plates for car mounts, and grips stuck on the back can block it or slow it down.
- Warm is expected. Some power is lost as heat, so the phone and pad grow warm — warmer than a cable charge. If the battery gets too warm, the phone protects itself and may hold the charge around 80% until it cools. Charge on a hard, flat surface; a bed or a pillow traps the heat.
Keep cards away from the magnets. Apple’s own warning, in plain words: never leave credit cards, security badges, passports, or key fobs between your iPhone and a MagSafe charger — the magnets can damage the card’s magnetic stripe or chip. A wallet-style case comes off for charging.
If it goes wrong
- Dead in the morning: it was off-center. Set the phone down again and watch for the charging symbol before you walk away. A magnetic pad ends this problem for good.
- Charging starts, stops, starts again: usually something sits between phone and pad — a thick case or a metal plate. Try one night with the case off to find out.
- Phone hot to the touch: move it off soft surfaces, take the case off, and let it cool. Warm is normal; too hot to hold comfortably is not.
- Nothing happens at all: check the pad’s own plug. A pad fed by a weak old wall plug cannot charge at full pace — and some will not start at all. The plug matters as much as the pad.
Words in this lesson
- Qi: the shared wireless-charging standard nearly every modern phone speaks — pronounced “chee.” If pad and phone both say Qi, they work together.
- MagSafe: Apple’s magnetic version for iPhone — the charger snaps into the perfect position by itself.
- Qi2: the newer version of the Qi standard, with the same magnet snap, now reaching Android phones too.
- Watt (W): how fast power flows. More watts means faster charging — when the phone, the pad, and the wall plug all support it.