TV Sound Straight Into Your Hearing Aids: The Streamer Bridge

A TV streamer is a small box that plugs into your TV and beams the sound straight into your hearing aids — clear voices at your volume, while the TV speakers stay at everyone else's. This lesson is the whole hookup, step by step. (Pairing your hearing aids with your phone is a different job, and it is already covered on this shelf in 'Hearing Aids & Your Phone' — this lesson is the TV side.)

Before you buy any box: the two-minute check

Some newer set-ups can send TV sound straight into your hearing aids with no streamer box at all. The box costs a few hundred dollars, so this check comes first — it takes two minutes and might save all of it.

If none of those doors open, the streamer box below is the reliable route — it is the one that works with nearly every TV and lets the room keep its speakers. That is what the rest of this lesson hooks up.

The one rule before anything else: brands must match

A streamer only speaks to hearing aids from its own family. Each hearing aid maker sells its own box — Phonak aids take the Phonak TV Connector, Oticon aids the Oticon TV Adapter, Widex the TV Play, ReSound and Starkey their own TV Streamers. A different brand's box will not pair, full stop. Streamers come from your hearing aid maker or your hearing office, and they cost — in the words of this shelf's hearing chart — a few hundred dollars. If you are not sure which box matches your aids, ask the hearing office before spending anything.

Step 1: Plug the box into the TV

  1. Give the streamer power. Plug its power cord into a wall socket (some draw power from a USB socket on the TV instead). A small light on the box should glow.
  2. Connect the sound cable — the optical cable is the best choice. It is also called a Toslink cable: a thin cable with squarish plugs. One end goes into the TV socket marked Optical Out or Digital Audio Out; the other end goes into the streamer.
  3. No optical socket? Use the plain round 3.5mm cable from the TV's headphone or audio-out socket to the streamer instead. One warning, straight from the makers' own manuals: on some TVs, plugging into the headphone socket switches the TV's speakers off for everyone. The optical socket does not do that — one more reason it is the first choice.
  4. If the box is connected but silent, the TV may need one setting changed: open the TV's Settings, then Sound, and set the digital sound output to the plain choice called PCM. That is the flavor of sound every streamer understands.
  5. If your TV sound runs through a soundbar: a soundbar plugged into the TV's socket marked ARC (or eARC) takes over the TV's sound — and on some TVs, the optical socket the streamer needs then goes quiet. So if the box is hooked up, set to PCM, and still silent, and a soundbar is in the picture, test the clash directly: unplug the soundbar's cable for one minute and see if your aids wake up. If they do, the two were fighting over the sound. The lasting fix is usually one TV setting — the sound output choice — or moving which socket feeds which box. That is a five-minute job for Sean with the remote in hand, and it is worth doing before anyone concludes the streamer is faulty.

Step 2: Pair your hearing aids to the box

  1. Put your hearing aids on (or hold them close) and stand within about a metre — three feet — of the streamer.
  2. Many streamers pair by themselves the first time they are powered up with the TV on: your hearing aids connect on their own and you hear a short confirmation beep in your ears. That beep means you are done.
  3. If nothing happens, press the Connect (pairing) button on the streamer — its light starts to blink. Then restart your hearing aids so they are ready to pair: for battery aids, open and close the battery doors; for rechargeable aids, turn them off and back on (or lift them out of the charger and put them back). Wait for the beep.
  4. You only pair once. After that, the aids find the streamer by themselves whenever the TV is on.

Everyday use

The honest scope: streamer boxes all follow the steps above, but the exact button names, lights, and app screens differ from brand to brand. The streamer's own booklet is the authority for your model, and pairing is something your hearing office does every day — there is no shame in letting them do the first hookup. Sean's part of the job is the TV side: the cables, the PCM setting, and making sure the speakers behave for everyone else in the room.

Words in this lesson

Straight 2 Work Tech, LLC — patient, plain-words tech help.
(813) 770-6082