← All questions

Printers

My printer will not print an entire document. What should I check?

437.My printer will not print an entire document. What should I check?

The printer starts — then stops. Or it prints the first pages and skips the rest, or the last page never comes. A document that prints part way is a different trouble from a printer that will not print at all, and it has its own short list of causes: the paper or ink ran out mid-job, a page-range setting left over from an earlier job, a stuck print queue, or the connection dropping during a long document. First, look at what you actually got and sort yours: stops mid-page or mid-document (the job died), whole pages missing (the job finished but pages are absent), or one page blank in the middle (often a blank page inside the document itself). Then work in this order.

  1. Check paper and ink first — a job can starve in the middle. A stack that runs out on page 7 of 10 leaves exactly this complaint, and so does a cartridge that gives up mid-document (later pages come out faint, streaked, then blank — this shelf’s blank-pages tip covers the ink side in full). Look at the tray with your eyes, not the screen: is there paper, is it the size the job expects, and did a page half-feed and stop? A printer paused for paper often resumes by itself once the tray is filled and its button is pressed — give it a minute before you reprint anything, or you will own two copies of the first half.
  2. Check the Pages setting — the leftover range. In the print window there is a choice like Pages: All or a box for a range (such as 1–3). If you once printed “just pages 2 and 3” of something — this site’s Printers lesson on printing just the pages you need teaches exactly that trick — the range can still be sitting there, faithfully printing part of every document since. Set it back to All (or Entire document) and print again. This one setting explains more “missing last pages” than any broken part.
  3. Clear the stuck job and send it once, cleanly. When a job half-prints and the queue jams, copies of the same job pile up and confuse everything after. Cancel the job properly (this shelf’s stuck-print-job tip walks it), then send the document once and wait. Windows: Settings → Bluetooth & devices → Printers & scanners → your printer → Open print queue — the queue should show just your one job, counting pages as it goes. Mac: System Settings → Printers & Scanners → your printer → Printer Queue. If the page count stalls at the same number every time, that number is a clue worth writing down.
  4. Test the connection with size in mind: print the document in two halves. Long, photo-heavy documents are big mouthfuls, and a weak Wi-Fi link to the printer can drop in the middle of one. Print pages 1–half using the Pages range (on purpose this time), then the rest. If both halves print cleanly, the printer and its settings are fine — the whole job was simply too much for the connection at once. The lasting fixes are the plain ones: print with the computer in the same room as the printer, or connect the printer with its USB cable for big jobs (this shelf’s USB-cable lesson covers it). Remember to set Pages back to All afterward.
  5. Restart the printer — fully off, not asleep. Turn the printer off with its power button, wait a slow count of 30, and turn it back on. A printer that has half-swallowed a job often holds the remains in its memory, and only a full restart clears its throat. Then send the document once more, whole, with Pages set to All.
  6. Read the pattern before you call it broken. The same page missing every time points at the document itself (that page may hold a picture the printer chokes on — try printing that single page alone). A different stopping point every time points at the connection or the queue. Every long document stopping, short ones fine, points at size (step 4). Write down which pattern yours is, plus the page it stops on, and bring that to Sean: “10-page document, stops on page 6, twice” is a report he can act on in minutes.
Sort it in one look: fades out — ink; stops dead with the tray empty — paper; always the same pages missing — the Pages range (step 2); halves print, whole does not — the connection (step 4). Part-printed documents feel like a dying printer, but the cause is nearly always something the job ran out of — paper, ink, room in the queue, or signal — not the printer itself.